To reproof a waterproof jacket, clean it first with a cleaner made for waterproofs, because dirt and body oils are often all that stops water beading. If the fabric still soaks up water after a wash, apply a reproofer: a wash-in product for jackets with no inner lining to wick sweat, or a spray-on for jackets with a mesh or wicking lining, so only the outside is treated. Then dry it as the product and the care label say, with gentle heat if both allow it, and test it with a sprinkle of water.
How do you know when a jacket needs reproofing?
A waterproof jacket keeps rain out with a membrane or coating inside, and sheds it with a water-repellent finish on the outer fabric. Reproofing renews that outer finish.
Sprinkle a little water on the shoulders and chest:
Advertisement
- It beads and rolls off: the finish is working. Leave it.
- It spreads and darkens the fabric, usually on the shoulders, cuffs and where a bag rubs first: the finish has worn or is clogged. This is called wetting out.
A jacket that wets out may not leak, since the membrane is still underneath, but the soaked outer fabric stops it breathing, so it feels cold and clammy inside. That clamminess is often mistaken for a leak.
Reproofing brings back the beading on a showerproof jacket too, but it will not make it waterproof.
Why clean it first?
Dirt, sweat, sun cream and smoke clog the finish and attract water. A good wash often brings the beading back by itself, and a reproofer will not bond properly to a dirty jacket.
- Check the care label for temperature, cycle and drying.
- Empty the pockets, close every zip and fasten the hook-and-loop tabs, so nothing snags.
- Clean the detergent drawer, so no fabric softener or powder residue gets into the wash.
- Use a cleaner made for waterproofs, not ordinary detergent, which can leave a residue that attracts water. Never use fabric softener.
- Wash it on the cycle the label gives, usually cool and gentle, and add an extra rinse.
Then dry it as the label allows and test the beading again. If water beads, you are done.
Wash-in or spray-on: which should you use?
Wash-in reproofers go into the drum after cleaning and coat the whole jacket, inside and out.
- Good for: jackets with no inner lining, softshells and most kids' waterproofs, where an even all-over coat helps.
- Less good for: jackets with a mesh or fabric lining designed to move sweat away from your body. Coating the lining too can make it hold moisture against you.
Spray-on reproofers are applied to the outside only.
- Good for: jackets with a wicking or mesh lining, and for topping up the areas that wear first, such as shoulders, hood and cuffs.
- Less good for: covering a whole jacket evenly, which takes care.
If you are unsure, spray-on is the safer choice for a lined jacket. Waxed cotton is different again: it is reproofed by rewaxing, not with either of these, as our guide to buying a second-hand waxed jacket explains.
How do you use a wash-in reproofer?
- Clean the jacket first, as above, and leave it damp.
- Put it back in the machine with the right amount of reproofer, following the bottle.
- Run the cycle the product gives, usually cool, with a low spin.
- Dry it as the product and care label direct.
How do you use a spray-on reproofer?
- Clean the jacket. Most sprays go on while it is still damp: check the bottle.
- Hang it outdoors or somewhere well ventilated.
- Spray evenly over the outside from the distance the product gives, overlapping as you go, with extra attention to the shoulders, hood and cuffs.
- Wipe off drips with a cloth after a couple of minutes.
- Let it dry, or apply heat if the instructions say so.
Does it need heat?
Some reproofers, and some jackets' factory finishes, work best after gentle heat, which helps the finish settle on the fibres. Others are made to work at room temperature, and the bottle says which.
- If the care label allows tumble drying and the product calls for heat, a short tumble on low is usual.
- If the label allows ironing, some products suggest a cool iron through a cloth instead.
- If the label says do not tumble dry or iron, let it air dry and choose a reproofer that does not need heat.
Never use more heat than the care label shows. Too much can damage the membrane and the seam tape.
What can reproofing not fix?
Reproofing renews the outer finish only. It will not repair:
- delamination, bubbles where the membrane has come away from the fabric
- seam tape that is peeling or missing inside
- a sticky or flaking coating on the inside
- holes and worn-through patches
If a clean, reproofed jacket still lets water in at the same places, look inside at the seams and shoulders. Our guides to buying a second-hand waterproof jacket and second-hand ski and snow wear cover these checks before you buy.
How often should you reproof?
Whenever the water stops beading after a clean. That might be every few washes for a jacket worn daily, or once a season for one worn on weekends. Clean it whenever it looks grubby, and it will need reproofing less.
Down jackets with a water-repellent shell can be reproofed too, after washing them the way our guide to washing a down jacket explains.
The short version
Test with water. If it wets out, clean it with a cleaner made for waterproofs, then test again. Still wetting out? Wash-in for unlined jackets, spray-on for lined ones, and only the heat the label and the product allow.
Advertisement
Find your next piece
Second-hand clothing from sellers across the UK, with measurements in cm where sellers add them and buyer protection at checkout.