REWEAR

Buying

Buying a second-hand waterproof jacket: what to check

Waterproof or showerproof, where to look inside for failed seam tape and peeling, the beading test to ask for, what can be fixed and what to pay.

A second-hand waterproof jacket is worth buying when the waterproof layer inside it is intact: seam tape lying flat along every seam, no bubbles or peeling on the inside, no sticky or flaking coating, zips that run cleanly, and a hood and cuffs whose adjusters still work. Rain soaking into the outside instead of beading off is usually a cleaning and reproofing job you can do at home. A failed membrane or lifting seam tape is not, so look inside the jacket before anything else.

Is it waterproof, or only showerproof?

  • Waterproof jackets have a waterproof layer and taped seams, so rain cannot get through the fabric or the stitching.
  • Water-resistant or showerproof jackets shed light rain, but their seams are usually not taped and they wet through in a downpour.

Labels on waterproofs often give a hydrostatic head in millimetres, such as 10,000 mm: the higher the figure, the more water pressure the fabric resists before it leaks. It describes the fabric when new, not the seams and zips, and not a jacket that has been worn for years.

How is a waterproof jacket made?

The outer fabric has a water-repellent finish that makes rain bead up and roll off. Underneath is what actually keeps water out: a thin membrane bonded to the fabric, or a waterproof coating on its inside.

  • 2-layer jackets have a loose mesh or fabric lining hanging inside, covering the membrane.
  • 2.5-layer jackets have a thin printed or sprayed layer inside instead, and feel slightly smooth or plasticky.
  • 3-layer jackets bond the outer fabric, membrane and inner fabric together. They are the most hard-wearing.

What should you check inside?

Ask for photos of the inside, especially the shoulders, the hood and the seams under the arms. On a 2-layer jacket, the seller may need to lift the lining.

  • Seam tape: the strips covering the seams should lie flat and stuck down. Lifting edges, wrinkled tape or missing sections let water in. A short lifted strip can be stuck back with seam sealer; tape peeling all over cannot be saved.
  • Delamination: bubbles or puckered patches where the membrane has come away from the outer fabric, often on the shoulders and back where a rucksack rubs, or after a jacket was washed or dried too hot. It cannot be repaired.
  • A sticky or flaking coating: on coated jackets the inside can turn tacky with age, or shed white or grey flakes, especially after damp storage. That coating is the waterproofing, so it is finished.

Zips, hood and cuffs

The main zip should run smoothly from top to bottom; on waterproof zips with a rubbery coating, look for cracking along the teeth. Storm flaps should close, pit zips should open and shut, and every zip pull should be there. A zip that only sticks can often be freed, as our guide to fixing a stuck zip shows. On Rewear, sellers can tag "Zip needs attention" as a flaw: look for a close-up, and ask what is wrong.

The hood's toggles should tighten it and a stiffened peak should hold its shape. Hook-and-loop cuff tabs clogged with fluff stop gripping, and the hem drawcord should still work.

How do you test the beading?

Ask the seller to sprinkle a little water on the shoulders and chest and tell you what happens, or to photograph it.

  • It beads and rolls off: the water-repellent finish is working.
  • It spreads and darkens the fabric: the finish has worn off. This is called wetting out.

A jacket that wets out does not necessarily leak, because the membrane is underneath, but it feels cold and clammy and stops breathing. A wash with a cleaner made for waterproofs, a reproofing treatment and, if the care label allows, a little heat usually bring the beading back. Our guide to reproofing a waterproof jacket shows how.

What sets a fair price

The fabric and the state of the inside matter more than how clean the outside looks. A jacket that only wets out is a good buy if the price allows for a wash and reproof. One with delamination, peeling tape or a sticky coating is no longer a waterproof, just a light shell for dry days, and should be priced that way or left.

What should you ask the seller?

  • "Has it been tumble dried, or washed with fabric softener?" Softener coats the fabric and stops it repelling water.
  • "Has it ever leaked, and where?"
  • "Has it been reproofed, and roughly how old is it?"
  • "Where has it been stored?" A damp loft is hard on coatings.

Will it fit over your layers?

A waterproof goes over everything else, so compare it with a jacket you wear over a fleece or jumper. A Rewear listing for a jacket or coat asks the seller for chest pit to pit, length, sleeve and shoulder. The sleeves should still cover your wrists with your arms raised, and the hood should go over a hat. For town rather than hills, see our guide to buying a second-hand Barbour or waxed jacket.

How do you test it when it arrives?

Do the beading test yourself, then wear it in the shower for a few minutes, or out in the rain, and check the inside of the seams and shoulders for damp patches. Do this before you confirm delivery in the app, since confirming is what pays the seller. If it leaks somewhere the listing did not mention, open a problem report on the order within 14 days of delivery.

The short version

Look inside first: flat seam tape, no bubbles, no sticky or flaking coating. Check the zips, hood and cuffs, and ask for the beading test. Wetting out is fixable with a wash and reproof; delamination and failed seam tape are not, so price them as a light shell or walk away.

Find your next piece

Second-hand clothing from sellers across the UK, with measurements in cm where sellers add them and buyer protection at checkout.

See what’s for saleSell on Rewear

More from the Rewear blog