REWEAR

Care

How to take up a hem without sewing: iron-on hemming tape

How to take up trousers, skirts and jeans with iron-on hemming tape: marking the length, fusing it, fabrics it ruins, one-night fixes and when to see a tailor.

To take up a hem without sewing, use iron-on hemming tape. Try the piece on with the shoes you will wear it with, pin the new length, press the fold, slip the tape inside it and fuse it with an iron and a damp cloth, one section at a time, then leave it to cool before you move it. For one night or a quick fix, double-sided fabric tape or small safety pins on the inside work without any heat. Lined, tailored, delicate or stretchy pieces, and jeans whose original hem you want to keep, are worth taking to a tailor.

How do you mark the right length?

  1. Put on the shoes you will wear most with it, since heels and trainers need different lengths.
  2. Fold the hem under and pin it where it looks right. For trousers, the front should just meet the top of your shoe, with a slight break.
  3. Measure the turn-up at the pin and keep it the same all the way round, measured in cm from the existing hem.

For trousers, a quicker way is to measure the inside leg, from the crotch seam to the hem, on a pair that is already the right length, and fold the new pair to match. Our measuring guide shows exactly where to hold the tape. A Rewear listing for jeans, trousers or shorts asks the seller for this same figure, so you can often tell before you buy how much would need taking up.

How do you use iron-on hemming tape?

Hemming tape is a strip of adhesive web that melts under the iron and bonds the fold to the garment. It lasts through washes and is the closest thing to a sewn hem.

  1. Wash and dry the garment first if it is new cotton or might shrink.
  2. Turn the hem up to the inside at your marked length and press the fold, at the iron setting the care label allows.
  3. Trim any excess if the turn-up is deeper than about 4 or 5 cm, so the hem is not bulky.
  4. Cut the tape to the length of the hem and slide it inside the fold, just below the raw edge, so none peeks out.
  5. Cover it with a damp tea towel and press the iron straight down on one section, for about 10 seconds or the time the packet gives. Do not slide or push the iron, which moves the tape.
  6. Lift, move along and repeat, overlapping each section slightly, until you have gone all the way round.
  7. Let it cool completely. The glue sets as it cools.
  8. Tug gently to check it has held, and press again where it has not.

Heavy fabrics such as denim may need a stronger, wider tape and a little longer under the iron.

Which fabrics should not have iron-on tape?

  • anything the care label says not to iron, or to iron only on a cool setting
  • silk and satin, which can mark and show the tape through
  • velvet, whose pile the iron crushes
  • sequinned and beaded fabric
  • leather and faux leather
  • sheer fabrics, where the tape shows
  • stretchy jersey, leggings and fleece, because the tape does not stretch and the hem can pop

For these, use fabric tape or pins for a night, or a tailor for good.

What are the best quick fixes for one night?

  • Double-sided fabric tape: press it firmly onto the inside of the hem allowance, fold up and press again. Take it off before washing.
  • Small safety pins: every 8 to 10 cm, inside, through the folded hem only, pointing sideways so they do not catch.
  • A neat turn-up on casual trousers.

How do you wash a taped hem?

Wash it inside out, at a temperature both the care label and the tape packet allow, and check it after the first few washes. Re-press any section that lifts.

To remove it later, warm the hem with the iron through a cloth and peel it apart while warm. Some glue may stay on the fabric, and a pressed fold line can remain visible on some fabrics, so iron-on tape is best thought of as permanent.

When should you see a tailor?

  • Lined trousers, skirts and coats, where the lining needs shortening separately.
  • Suits and tailored trousers, where the finish shows.
  • Jeans you want to keep the original hem on: a tailor can shorten them and reattach the factory hem so the fading stays.
  • Tapered legs with a lot to take off, since the leg is narrower higher up and the fold will not lie flat.
  • Flared, pleated or circle skirts, curved hems, and hems with slits, vents or cuffs.
  • Anything precious, where you would hate to get it wrong.

If you would rather sew it yourself, our guide to simple repairs before you sell shows the slip stitch for a hem.

Buying second-hand trousers that are too long?

Check the inside leg on the listing against a pair that fits, and you will know how much needs taking up. Our guides to buying jeans online that fit and how trousers should fit explain the other measurements and how much break to aim for. If a figure is missing, ask the seller, and ask whether the hem has ever been altered.

If you sell a piece you have shortened, say so in the description and measure the inside leg again, so the figure on the listing is the one it is now.

The short version

Pin the length with the right shoes on, press the fold and fuse iron-on hemming tape under a damp cloth, pressing without sliding, then let it cool. Use fabric tape or pins for a night, keep heat off delicate and stretchy fabrics, and take lined, tailored and precious pieces to a tailor.

Find your next piece

Second-hand clothing from sellers across the UK, with measurements in cm where sellers add them and buyer protection at checkout.

See what’s for saleSell on Rewear

More from the Rewear blog