REWEAR

Fit and sizing

How should a blazer fit? Shoulders, buttons and sleeves

How a blazer should fit at the shoulders, chest, fastening button, sleeves and hem, in men's and women's cuts, and what a tailor can and cannot change.

A blazer fits when the shoulder seams sit at the edge of your shoulders with no dent below them, the fastening button closes without the fabric pulling into an X, the sleeves end at your wrist bone with about a centimetre of shirt cuff showing, and the length suits the cut. Get the shoulders right first: a tailor can shorten sleeves and take in a waist, but shoulders are very hard to change. To check a second-hand blazer, compare its shoulder, chest, sleeve and length in cm with a jacket that fits you.

The fit checklist

Do it up and check in a mirror, side-on too.

  • Shoulders: the seam sits at the edge of your shoulder bone and the sleeve hangs straight down, with no dent at the top.
  • Front: the lapels lie flat, and nothing pulls into an X around the button. A flat hand slides inside the front without strain.
  • Collar: it sits against your shirt collar at the back of the neck, with no gap.
  • Back: smooth, without folds below the collar, and the vents hang closed.
  • Sleeves: they end at your wrist bone, with about 1 cm of shirt cuff showing.
  • Length: on a classic cut, the hem covers your seat.

Where should the shoulders of a blazer sit?

The shoulder seam should sit at the edge of your shoulder bone.

  • Too narrow: the fabric pulls across your upper back, creases run from the collar towards the arms, and reaching forward feels tight.
  • Too wide: the padding extends past your shoulder, and a dent or ripple appears at the top of the sleeve.

A quick test: stand side-on to a wall and lean your shoulder against it. If the padding touches the wall well before your arm does, the shoulders are too wide.

A soft, unstructured blazer is more forgiving, and an oversized cut is meant to sit lower. On a structured blazer, a shoulder figure within a centimetre or so of one that fits you is a good sign; two or more centimetres narrower will usually pull.

How much room should a blazer have in the chest?

A listing's pit to pit is half the way round, so double it first. As a rough guide, a tailored blazer measures around 8 to 15 cm more than your chest: slim cuts nearer the lower end, relaxed ones nearer the top, and oversized styles well beyond. For wearing over knitwear, you need the upper end.

Menswear labels often give a chest size in inches with a length fitting, such as 40R: a 40-inch chest, regular length, with short and long fittings either side. That is the body the jacket was cut for, so the jacket itself measures more.

How long should blazer sleeves be?

With your arms relaxed by your sides, the sleeve should end where your wrist meets your hand. Over a shirt, about 1 cm of shirt cuff showing is the classic look. Over a T-shirt or a fine knit, the sleeve should still reach the wrist bone, or a touch lower. Our guide to how a men's shirt should fit covers the cuff underneath.

How long should a blazer be?

  • Classic blazers cover your seat. The traditional check: with your arms relaxed, you can curl your fingers under the hem.
  • Modern cuts often finish a little shorter, at the top of the seat.
  • Women's blazers run from cropped, ending at the waist, to longline, reaching the upper thigh. A cropped blazer suits high-waisted trousers and skirts; a longline one covers a long jumper.

Where should the buttons sit?

The fastening button, the top one on a two-button blazer, the middle one on a three-button and the only one on a single-button, should sit at or just above your navel. Too low and your legs look shorter; too high and the blazer looks a size too small.

The traditional rule on men's single-breasted blazers is to leave the bottom button undone. Women's blazers vary, so follow the design.

What can a tailor change on a blazer?

  • Usually straightforward: shortening the sleeves, or lengthening them a little if there is spare fabric turned up inside. Taking in or letting out the waist a little at the back and side seams.
  • Harder: sleeves with working buttonholes at the cuff, which have to be altered from the shoulder end, and shortening the body, which only works by a centimetre or two before the pockets sit too low.
  • Not worth it: shoulders that are too wide or too narrow, a chest that will not close, or a blazer that is too short.

A blazer that is right in the shoulders and chest but long in the sleeve is often a good buy; one that is wrong in the shoulders is not, however good the cloth.

How do you check a second-hand blazer in cm?

On Rewear, blazers are listed under Jackets & coats, Blazers & waistcoats or Suits & tailoring, and all three ask for the same four figures, taken flat. Lay a blazer that fits you on a bed, do it up, and compare in this order:

  1. Shoulder: seam to seam across the back.
  2. Chest: pit to pit, armpit to armpit.
  3. Sleeve: shoulder seam to cuff.
  4. Length: from the highest point of the shoulder, beside the collar, to the hem.

Rewear's Terms count a hand measurement within 2 cm of the listed figure as accurate, so do not buy a blazer that only just works on paper. If a figure is missing, ask: "Could you measure the shoulder, seam to seam across the back, laid flat?" Our Will it fit? checker compares a jacket's chest with yours.

Our guide to buying a second-hand suit covers the cloth and the wear points, buying a second-hand dinner suit covers black tie, and one blazer, five ways shows how much wear a good one gives.

Find your next piece

Second-hand clothing from sellers across the UK, with measurements in cm where sellers add them and buyer protection at checkout.

See what’s for saleSell on Rewear

More from the Rewear blog